|
1000 |
dC0951 Timeout Fault |
|
1100 |
Cycle-Up Convergence Timed Out |
|
3001 |
No PR Drive Motor Encoder Pulses |
|
3002 |
No PR Belt Hole Detected |
|
3003 |
PR Belt IB / OB Tracking Fault |
|
3004 |
PR Belt IB / OB Tracking Fault |
|
3005 |
PR Belt Steering Motor Failed to Home |
|
3006 |
PR Belt Steering Motor Missing +36 VDC |
|
3007 |
PR Belt Steering Motor Winding A/B Fault |
|
3008 |
PR Belt Steering Motor Winding A/B Fault |
|
3009 |
PRBC Cannot Communicate With DSC 5 |
|
3010 |
PR Belt Sync Failure |
|
3014 |
PR Drive Motor Velocity Error |
|
3015 |
PR Belt Drive Motor Open |
|
3016 |
PR Belt Torque Assist Motor Open |
|
3019 |
PRBC Command Timeout |
|
3020 |
No Belt Hole Signal at MOBi/CSR PWB |
|
3021 |
Unexpected Belt Hole Detected |
|
3022 |
No Belt Hole Signal at Marker PWB |
|
3023 |
PR Belt Edge Lower Sensor Q908 Open or Shorted |
|
3024 |
PR Belt Edge Upper Sensor Q907 Open or Shorted |
|
3026 |
Pretransfer Discorotron Arcing |
|
3027 |
Pretransfer HVPS Overtemperature |
|
3028 |
Pretransfer HVPS Missing 15 or 36 VDC |
|
3029 |
Pretransfer Grid Overcurrent |
|
3030 |
PR Belt Inboard Tracking Fault at Lower Sensor |
|
3031 |
Pretransfer Wire Open Circuit |
|
3033 |
Pretransfer HVPS Non-Specific Fault |
|
3037 |
HAK Motor Missing +36 VDC |
|
3038 |
HAK Motor Winding A Fault |
|
3039 |
HAK Motor Winding B Fault |
|
3040 |
PR Belt Outboard Tracking Fault at Lower Sensor |
|
3048 |
ATA Power Supply Overcurrent |
|
3049 |
ATA Power Supply Voltage Fault |
|
3050 |
ATA Power Supply Fault |
|
3060 |
Transfer Dicorotron Shield Voltage Too High |
|
3061 |
Transfer or Detack Dicorotron Shield Fault |
|
3062 |
Transfer Dicorotron 2 Shield Fault |
|
3066 |
Transfer/Detack PS Overtemperature or Wire Current Fault |
|
3067 |
Transfer or Detack Wire Current Out of Range |
|
3076 |
Preclean Dicorotron Wire Arcing |
|
3077 |
Preclean Dicorotron Shield Arcing |
|
3078 |
Preclean HVPS Overtemperature |
|
3079 |
Preclean HVPS Missing 15 or 36 VDC |
|
3080 |
Preclean Shield Voltage Out of Range |
|
3081 |
Preclean Wire Open Circuit |
|
3083 |
Preclean HVPS Non-Specific Fault |
|
3087 |
Cleaner Motor Velocity Error |
|
3088 |
Cleaner Motor Power Saturation |
|
3089 |
Cleaner Motor Failed to Start |
|
3090 |
Cleaner Motor Harness Fault |
|
3092 |
Cleaner Power Supply Brush 1 / Brush 2 Overcurrent |
|
3093 |
Cleaner Power Supply Brush 1 / Brush 2 Overcurrent |
|
3101 |
Waste Developer Container Full or Missing |
|
3102 |
Waste Developer Container Not Present or Full Too Long |
|
3108 |
TRC Patch Read Failure |
|
3109 |
TRC Measurement Variation Limit Exceeded Fault |
|
3110 |
TRC Clean Belt Reading Above Threshold Fault |
|
3111 |
Center ETAC Diffuse Clean Belt Reading Out of Range |
|
3114 |
Center ETAC Sensor Offset Voltage Out of Range |
|
3115 |
Center ETAC Diffuse Clean Belt Signature Fault |
|
3116 |
Center ETAC Specular Clean Belt Signature Fault |
|
3117 |
Outboard ETAC Diffuse Clean Belt Reading Out of Range |
|
3120 |
Outboard ETAC Sensor Offset Voltage Out of Range |
|
3121 |
Outboard ETAC Diffuse Clean Belt Signature Fault |
|
3122 |
Outboard ETAC Specular Clean Belt Signature Fault |
|
3123 |
Inboard ETAC Diffuse Clean Belt Reading Out of Range |
|
3126 |
Inboard ETAC Sensor Offset Voltage Out of Range |
|
3127 |
Inboard ETAC Diffuse Clean Belt Signature Fault |
|
3128 |
Inboard ETAC Specular Clean Belt Signature Fault |
|
3129 |
Average Specular Clean Belt Readings Below Threshold |
|
3144 |
PR Belt Residual Voltage Too High |
|
3145 |
Belt Signature Acquisition On Cycle Up Disabled |
|
3151 |
Missing PR Belt Edge Data |
|
3154 |
PR Belt Static Eliminator Power Supply Overcurrent |
|
3158 |
Center ETAC LED Intensity Too High |
|
3159 |
Front ETAC LED Intensity Too High |
|
3160 |
Rear ETAC LED Intensity Too High |
|
3161 |
Center ETAC LED Intensity Out of Range |
|
3162 |
Outboard ETAC LED Intensity Out of Range |
|
3163 |
Inboard ETAC LED Intensity Out of Range |
|
3164 |
Center ETAC Clean Patch Fault |
|
3165 |
Outboard ETAC Clean Patch Fault |
|
3166 |
Inboard ETAC Clean Patch Fault |
|
3167 |
Center ETAC Not Reading Solid Area Patch |
|
3168 |
Outboard ETAC Not Reading Solid Area Patch |
|
3170 |
TRC Solid Area Patch Readings Out of Range Fault |
|
3171 |
Center ETAC LED Intensity Out of Range |
|
3172 |
Front ETAC LED Intensity Out of Range |
|
3173 |
Front ETAC LED Intensity Out of Range |
|
3181 |
TAB Engagement Motor Missing 36 VDC |
|
3184 |
TAB Engagement Motor Winding A /B Failure |
|
3185 |
TAB Engagement Motor Winding A /B Failure |
|
3186 |
TAB Engagement Motor Rehome Fault |
|
3188 |
TAB Width Motor Missing 36 VDC |
|
3191 |
TAB Width Motor Winding A / B Failure |
|
3192 |
TAB Width Motor Winding A / B Failure |
|
3193 |
TAB Width Motor Rehome Fault |
|
3206 |
DHTC 1 PWB Missing +36 VDC |
|
3311 |
Dry Ink Bottle1 (M) Motor Missing +36 VDC |
|
3312 |
Dry Ink Bottle 2 (Y) Motor Missing +36 VDC |
|
3313 |
Dry Ink Bottle 3 (C) Motor Missing +36 VDC |
|
3314 |
Dry Ink Bottle 4 (K) Motor Missing +36 VDC |
|
3331 |
Dry Ink Bottle 1 (M) Motor Winding A Fault |
|
3332 |
Dry Ink Bottle 2 (Y) Motor Winding A Fault |
|
3333 |
Dry Ink Bottle 3 (C) Motor Winding A Fault |
|
3334 |
Dry Ink Bottle 4 (K) Motor Winding A Fault |
|
3341 |
Dry Ink Bottle 1 (M) Motor Winding B Fault |
|
3342 |
Dry Ink Bottle 2 (Y) Motor Winding B Fault |
|
3343 |
Dry Ink Bottle 3 (C) Motor Winding B Fault |
|
3344 |
Dry Ink Bottle 4 (K) Motor Winding B Fault |
|
3361 |
Dispense Auger 1 (M) Motor Missing +36 VDC |
|
3362 |
Dispense Auger 2 (Y) Motor Missing +36 VDC |
|
3363 |
Dispense Auger 3 (C) Motor Missing +36 VDC |
|
3364 |
Dispense Auger 4 (K) Motor Missing +36 VDC |
|
3381 |
Dispense Auger 1 (M) Motor Winding A Fault |
|
3382 |
Dispense Auger 2 (Y) Motor Winding A Fault |
|
3383 |
Dispense Auger 3 (C) Motor Winding A Fault |
|
3384 |
Dispense Auger 4 (K) Motor Winding A Fault |
|
3391 |
Dispense Auger 1 (M) Motor Winding B Fault |
|
3392 |
Dispense Auger 2 (Y) Motor Winding B Fault |
|
3393 |
Dispense Auger 3 (C) Motor Winding B Fault |
|
3394 |
Dispense Auger 4 (K) Motor Winding B Fault |
|
3410 |
ILS Temperature Change Recalibration |
|
3501 |
Patch Generator LED Intensity at Maximum |
|
3502 |
Patch Generator LED Intensity at Minimum |
|
3503 |
Patch Generator LED Intensity Convergence Fault |
|
3601 |
Dry Ink Bottle CRUM 1 (M) Communication Loss |
|
3602 |
Dry Ink Bottle CRUM 2 (Y) Communication Loss |
|
3603 |
Dry Ink Bottle CRUM 3 (C) Communication Loss |
|
3604 |
Dry Ink Bottle CRUM 4 (K) Communication Loss |
|
3606 |
DSC12 - ILS Position Stepper Motor Controller Communication Fault |
|
3607 |
ILS Rig Position Stepper Motor Missing 36 Volts Fault |
|
3608 |
ILS Rig Position Stepper Motor Winding A Fault |
|
3609 |
ILS Rig Position Stepper Motor Winding B Fault |
|
3611 |
Dry Ink Bottle CRUM 1 (M) Communication Warning |
|
3612 |
Dry Ink Bottle CRUM 2 (Y) Communication Warning |
|
3613 |
Dry Ink Bottle CRUM 3 (C) Communication Warning |
|
3614 |
Dry Ink Bottle CRUM 4 (K) Communication Warning |
|
3621 |
Dry Ink CRUM Coupler 1 (M) Communication Loss |
|
3622 |
Dry Ink CRUM Coupler 2 (Y) Communication Loss |
|
3623 |
Dry Ink CRUM Coupler 3 (C) Communication Loss |
|
3624 |
Dry Ink CRUM Coupler 4 (K) Communication Loss |
|
3631 |
Dry Ink CRUM Coupler 1 (M) Communication Loss Warning |
|
3632 |
Dry Ink CRUM Coupler 2 (Y) Communication Loss Warning |
|
3633 |
Dry Ink CRUM Coupler 3 (C) Communication Loss Warning |
|
3634 |
Dry Ink CRUM Coupler 4 (K) Communication Loss Warning |
|
3641 |
Dry Ink Bottle CRUM 1 (M) Write Failure |
|
3642 |
Dry Ink Bottle CRUM 2 (Y) Write Failure |
|
3643 |
Dry Ink Bottle CRUM 3 (C) Write Failure |
|
3644 |
Dry Ink Bottle CRUM 4 (K) Write Failure |
|
3651 |
Dry Ink Bottle CRUM 1 (M) Write Warning |
|
3652 |
Dry Ink Bottle CRUM 2 (Y) Write Warning |
|
3653 |
Dry Ink Bottle CRUM 3 (C) Write Warning |
|
3654 |
Dry Ink Bottle CRUM 4 (K) Write Warning |
|
3661 |
Dry Ink Bottle CRUM 1 (M) Invalid |
|
3662 |
Dry Ink Bottle CRUM 2 (Y) Invalid |
|
3663 |
Dry Ink Bottle CRUM 3 (C) Invalid |
|
3664 |
Dry Ink Bottle CRUM 4 (K) Invalid |
|
3671 |
Dry Ink Bottle CRUM 1 (M) At End of Life |
|
3672 |
Dry Ink Bottle CRUM 2 (Y) At End of Life |
|
3673 |
Dry Ink Bottle CRUM 3 (C) At End of Life |
|
3674 |
Dry Ink Bottle CRUM 4 (K) At End of Life |
|
3676 |
Dry Ink Bottle CRUM 1 (M) Product Mismatch |
|
3677 |
Dry Ink Bottle CRUM 2 (Y) Product Mismatch |
|
3678 |
Dry Ink Bottle CRUM 3 (C) Product Mismatch |
|
3679 |
Dry Ink Bottle CRUM 4 (K) Product Mismatch |
|
3681 |
Dry Ink Bottle CRUM 1 (M) Station Mismatch |
|
3682 |
Dry Ink Bottle CRUM 2 (Y) Station Mismatch |
|
3683 |
Dry Ink Bottle CRUM 3 (C) Station Mismatch |
|
3684 |
Dry Ink Bottle CRUM 4 (K) Station Mismatch |
|
3686 |
Dry Ink Bottle CRUM 1 (M) Product Configuration Mismatch |
|
3687 |
Dry Ink Bottle CRUM 2 (Y) Product Configuration Mismatch |
|
3688 |
Dry Ink Bottle CRUM 3 (C) Product Configuration Mismatch |
|
3689 |
Dry Ink Bottle CRUM 4 (K) Product Configuration Mismatch |
|
3691 |
Dry Ink Bottle CRUM 1 (M) Contract License Mismatch |
|
3692 |
Dry Ink Bottle CRUM 2 (Y) Contract License Mismatch |
|
3693 |
Dry Ink Bottle CRUM 3 (C) Contract License Mismatch |
|
3694 |
Dry Ink Bottle CRUM 4 (K) Contract License Mismatch |
|
3696 |
Dry Ink Bottle CRUM 1 (M) Geographic Region License Mismatch |
|
3697 |
Dry Ink Bottle CRUM 2 (Y) Geographic Region License Mismatch |
|
3698 |
Dry Ink Bottle CRUM 3 (C) Geographic Region License Mismatch |
|
3699 |
Dry Ink Bottle CRUM 4 (K) Geographic Region License Mismatch |
|
3706 |
ILS Rig Position Stepper Motor Rehome Fault |
|
3707 |
ILS USB Communication Fault |
|
3708 |
ILS Command Fault |
|
3709 |
ILS MIB Communication Fault |
|
3750 |
Carrier Hopper Empty Fault |
|
3751 |
Magenta Carrier Dispense Fault |
|
3752 |
Yellow Carrier Dispense Fault |
|
3753 |
Cyan Carrier Dispense Fault |
|
3754 |
Black Carrier Dispense Fault |
|
3755 |
Carrier Hopper Open Too Long Fault |
|
4021 |
HSD 1 (M) Power Supply Overload |
|
4022 |
HSD 2 (Y) Power Supply Overload |
|
4023 |
HSD 3 (C) Power Supply Overload |
|
4024 |
HSD 4 (K) Power Supply Overload |
|
4031 |
Charge 1 (M) Dicorotron Wire Arc |
|
4032 |
Charge 2 (Y) Dicorotron Wire Arc |
|
4033 |
Charge 3 (C) Dicorotron Wire Arc |
|
4034 |
Charge 4 (K) Dicorotron Wire Arc |
|
4041 |
Charge 1 (M) AC HVPS Overtemperature |
|
4042 |
Charge 2 (Y) AC HVPS Overtemperature |
|
4043 |
Charge 3 (C) AC HVPS Overtemperature |
|
4044 |
Charge 4 (K) AC HVPS Overtemperature |
|
4051 |
Charge 1 (M) AC HVPS Missing 15 or 36 VDC |
|
4052 |
Charge 2 (Y) AC HVPS Missing 15 or 36 VDC |
|
4053 |
Charge 3 (C) AC HVPS Missing 15 or 36 VDC |
|
4054 |
Charge 4 (K) AC HVPS Missing 15 or 36 VDC |
|
4061 |
Charge 1 (M) Discorotron Grid Overcurrent |
|
4062 |
Charge 2 (Y) Discorotron Grid Overcurrent |
|
4063 |
Charge 3 (C) Discorotron Grid Overcurrent |
|
4064 |
Charge 4 (K) Discorotron Grid Overcurrent |
|
4071 |
Charge 1 (M) Discorotron Wire Overcurrent Fault |
|
4072 |
Charge 2 (Y) Discorotron Wire Overcurrent Fault |
|
4073 |
Charge 3 (C) Discorotron Wire Overcurrent Fault |
|
4074 |
Charge 4 (K) Discorotron Wire Overcurrent Fault |
|
4075 |
Pretransfer HVPS Overcurrent Fault |
|
4076 |
Preclean HVPS Overcurrent Fault |
|
4081 |
Charge 1 (M) Dicorotron Wire Open Circuit |
|
4082 |
Charge 2 (Y) Dicorotron Wire Open Circuit |
|
4083 |
Charge 3 (C) Dicorotron Wire Open Circuit |
|
4084 |
Charge 4 (K) Discorotron Wire Open Circuit |
|
4093 |
Charge 3 (C) DC HVPS Overtemperature |
|
4094 |
Charge 4 (K) DC HVPS Overtemperature |
|
4103 |
Charge 3 (C) DC HVPS Missing 15 VDC |
|
4104 |
Charge 4 (K) DC HVPS Missing 15VDC |
|
4113 |
Charge 3 (C) Pinscorotron Arc |
|
4114 |
Charge 4 (K) Pinscorotron Arc |
|
4123 |
Charge 3 (C) Pinscorotron Grid current Too High |
|
4124 |
Charge 4 (K) Pinscorotron Grid current Too High |
|
4133 |
Charge 3 (C) Pinscorotron Grid Open Circuit |
|
4134 |
Charge 4 (K) Pinscorotron Open Circuit |
|
4143 |
Charge 3 (C) Pinscorotron Pin Open Circuit |
|
4144 |
Charge 4 (K) Pinscorotron Pin Open Circuit |
|
4150 |
Xerox Special Formulation Magenta Dry Ink Low / Empty |
|
4151 |
Magenta Dry Ink Low / Empty |
|
4152 |
Yellow Dry Ink Low / Empty |
|
4154 |
Black Dry Ink Low / Empty |
|
4160 |
Xerox Special Formulation Magenta Dry Ink Low / Empty |
|
4161 |
Magenta Dry Ink Low / Empty |
|
4162 |
Yellow Dry Ink Low / Empty |
|
4163 |
Cyan Dry Ink Low / Empty |
|
4164 |
Black Dry Ink Low / Empty |
|
4171 |
Magenta Low Dry Ink Confirmation Requested |
|
4172 |
Yellow Low Dry Ink Confirmation Requested |
|
4173 |
Cyan Low Dry Ink Confirmation Requested |
|
4174 |
Black Low Dry Ink Confirmation Requested |
|
4181 |
Magenta Low Toner Sensor Reading Fault |
|
4182 |
Yellow Low Toner Sensor Reading Fault |
|
4183 |
Cyan Low Toner Sensor Reading Fault |
|
4184 |
Black Low Toner Sensor Reading Failure |
|
4201 |
Developer 1 (M) Donor Roll Motor Harness Fault |
|
4202 |
Developer 2 (Y) Donor Roll Motor Harness Fault |
|
4203 |
Developer 3 (C) Donor Roll Motor Harness Fault |
|
4204 |
Developer 4 (K) Donor Roll Motor Harness Fault |
|
4211 |
Developer 1 (M) Donor Roll Motor Failed to Start |
|
4212 |
Developer 2 (Y) Donor Roll Motor Failed to Start |
|
4213 |
Developer 3 (C) Donor Roll Motor Failed to Start |
|
4214 |
Developer 4 (K) Donor Roll Motor Failed to Start |
|
4221 |
Developer 1 (M) Donor Roll Motor Velocity Error |
|
4222 |
Developer 2 (Y) Donor Roll Motor Velocity Error |
|
4223 |
Developer 3 (C) Donor Roll Motor Velocity Error |
|
4224 |
Developer 4 (K) Donor Roll Motor Velocity Error |
|
4231 |
Developer 1 (M) Donor Roll Motor Power Saturation |
|
4232 |
Developer 2 (Y) Donor Roll Motor Power Saturation |
|
4233 |
Developer 3 (C) Donor Roll Motor Power Saturation |
|
4234 |
Developer 4 (K) Donor Roll Motor Power Saturation |
|
4251 |
Developer 1 (M) Mag Roll Motor Harness Fault |
|
4252 |
Developer 2 (Y) Mag Roll Motor Harness Fault |
|
4253 |
Developer 3 (C) Mag Roll Motor Harness Fault |
|
4254 |
Developer 4 (K) Mag Roll Motor Harness Fault |
|
4261 |
Developer 1 (M) Mag Roll Motor Failed to Start |
|
4262 |
Developer 2 (Y) Mag Roll Motor Failed to Start |
|
4263 |
Developer 3 (C) Mag Roll Motor Failed to Start |
|
4264 |
Developer 4 (K) Mag Roll Motor Failed to Start |
|
4271 |
Developer 1 (M) Mag Roll Motor Velocity Error |
|
4272 |
Developer 2 (Y) Mag Roll Motor Velocity Error |
|
4273 |
Developer 3 (C) Mag Roll Motor Velocity Error |
|
4274 |
Developer 4 (K) Mag Roll Motor Velocity Error |
|
4281 |
Developer 1 (M) Mag Roll Motor Power Saturation |
|
4282 |
Developer 2 (Y) Mag Roll Motor Power Saturation |
|
4283 |
Developer 3 (C) Mag Roll Motor Power Saturation |
|
4284 |
Developer 4 (K) Mag Roll Motor Power Saturation |
|
4291 |
Developer 1 (M) Harness Disconnected |
|
4292 |
Developer 2 (Y) Harness Disconnected |
|
4293 |
Developer 3 (C) Harness Disconnected |
|
4294 |
Developer 4 (K) Harness Disconnected |
|
4301 |
Charge 1 (M) PR Residual Voltage Too High |
|
4302 |
Charge 2 (Y) PR Residual Voltage Too High |
|
4303 |
Charge 3 (C) PR Residual Voltage Too High |
|
4304 |
Charge 4 (K) PR Residual Voltage Too High |
|
4311 |
Charge 1 (M) Discorotron Grid Voltage at Minimum |
|
4312 |
Charge 2 (Y) Discorotron Grid Voltage at Minimum |
|
4313 |
Charge 3 (C) Discorotron Grid Voltage at Minimum |
|
4314 |
Charge 4 (K) Discorotron Grid Voltage at Minimum |
|
4321 |
Charge 1 (M) Discorotron Grid Voltage at Maximum |
|
4322 |
Charge 2 (Y) Discorotron Grid Voltage at Maximum |
|
4323 |
Charge 3 (C) Discorotron Grid Voltage at Maximum |
|
4324 |
Charge 4 (K) Discorotron Grid Voltage at Maximum |
|
4333 |
Charge 3 (C) Pinscorotron Grid Voltage at Minimum |
|
4334 |
Charge 4 (K) Pinscorotron Grid Voltage at Minimum |
|
4343 |
Charge 3 (C) Pinscorotron Grid Voltage at Maximum |
|
4344 |
Charge 4 (K) Grid Pinscorotron Voltage at Maximum |
|
4351 |
ROS 1 (M) Exposure at Minimum |
|
4352 |
ROS 2 (Y) Exposure at Minimum |
|
4353 |
ROS 3 (C) Exposure at Minimum |
|
4354 |
ROS 4 (K) Exposure at Minimum |
|
4361 |
ROS 1 (M) Exposure at Maximum |
|
4362 |
ROS 2 (Y) Exposure at Maximum |
|
4363 |
ROS 3 (C) Exposure at Maximum |
|
4364 |
ROS 4 (K) Exposure at Maximum |
|
4371 |
Charge 1 (M) ESV Continuous at Minimum |
|
4372 |
Charge 2 (Y) ESV Continuous at Minimum |
|
4373 |
Charge 3 (C) ESV Continuous at MInimum |
|
4374 |
Charge 4 (K) ESV Continuous at Minimum |
|
4381 |
Charge 1 (M) ESV Continuous at Maximum |
|
4382 |
Charge 2 (Y) ESV Continuous at Maximum |
|
4383 |
Charge 3 (C) ESV Continuous at Maximum |
|
4384 |
Charge 4 (K) ESV Continuous at Maximum |
|
4411 |
Station 1 (M) Vmc at Minimum |
|
4412 |
Station 2 (Y) Vmc at Minimum |
|
4413 |
Station 3 (C) Vmc at Minimum |
|
4414 |
Station 4 (K) Vmc at Minimum |
|
4431 |
Station 1 (M) Vmc at Maximum |
|
4432 |
Station 2 (Y) Vmc at Maximum |
|
4433 |
Station 3 (C) Vmc at Maximum |
|
4434 |
Station 4 (K) Vmc at Maximum |
|
4441 |
Station 1 (M) Level 2 Timeout |
|
4442 |
Station 2 (Y) Level 2 Timeout |
|
4443 |
Station 3 (C) Level 2 Timeout |
|
4444 |
Station 4 (K) Level 2 Timeout |
|
4451 |
Developer 1 (M) Vmag at Minimum |
|
4452 |
Developer 2 (Y) Vmag at Minimum |
|
4453 |
Developer 3 (C) Vmag at Minimum |
|
4454 |
Developer 4 (K) Vmag at Minimum |
|
4461 |
Developer 1 (M) Vmag Voltage at Maximum |
|
4462 |
Developer 2 (Y) Vmag Voltage at Maximum |
|
4463 |
Developer 3 (C) Vmag at Maximum |
|
4464 |
Developer 4 (K) Vmag at Maximum |
|
4471 |
Developer 1 (M) Toner Concentration Out Of Range |
|
4472 |
Developer 2 (Y) Toner Concentration Out Of Range |
|
4473 |
Developer 3 (C) Toner Concentration Out Of Range |
|
4474 |
Developer 4 (K) Toner Concentration Out Of Range |
|
4481 |
Developer 1 (M) TC Sensor Reading Out of Range |
|
4482 |
Developer 2 (Y) TC Sensor Reading Out of Range |
|
4483 |
Developer 3 (C) TC Sensor Reading Out of Range |
|
4484 |
Developer 4 (K) TC Sensor Reading Out of Range |
|
4531 |
Station 1 (M) Level 2 Readings Out of Range and Vmag at Lower Limit |
|
4532 |
Station 2 (Y) Level 2 Readings Out of Range and Vmag at Lower Limit |
|
4533 |
Station 3 (C) Level 2 Readings Out of Range and Vmag at Lower Limit |
|
4534 |
Station 4 (K) Level 2 Readings Out of Range and Vmag at Lower Limit |
|
4541 |
Station 1 (M) Level 2 Readings Out of Range and Vmag at Upper Limit |
|
4542 |
Station 2 (Y) Level 2 Readings Out of Range and Vmag at Upper Limit |
|
4543 |
Station 3 (C) Level 2 Readings Out of Range and Vmag at Upper Limit |
|
4544 |
Station 4 (K) Level 2 Readings Out of Range and Vmag at Upper Limit |
|
4551 |
Station 1 (M) Level 2 Readings Out of Range and Laser Power at Lower Limit |
|
4552 |
Station 2 (Y) Level 2 Readings Out of Range and Laser Power at Lower Limit |
|
4553 |
Station 3 (C) Level 2 Readings Out of Range and Laser Power at Lower Limit |
|
4554 |
Station 4 (K) Level 2 Readings Out of Range and Laser Power at Lower Limit |
|
4571 |
Developer 1 (M) TC Too Low During Retoning |
|
4572 |
Developer 2 (Y) TC Too Low During Retoning |
|
4573 |
Developer 3 (C) TC Too Low During Retoning |
|
4574 |
Developer 4 (K) TC Too Low During Retoning |
|
4601 |
Developer 1 Temperature Too High |
|
4602 |
Developer 2 Temperature Too High |
|
4603 |
Developer 3 Temperature Too High |
|
4604 |
Developer 4 Temperature Too High |
|
4631 |
Developer 1 (M) TC Sensor Count Too Low |
|
4632 |
Developer 2 (Y) TC Sensor Count Too Low |
|
4633 |
Developer 3 (C) TC Sensor Count Too Low |
|
4634 |
Developer 4 (K) TC Sensor Count Too Low |
|
4641 |
Developer 1 (M) TC High Too Long During Detoning |
|
4642 |
Developer 2 (Y) TC High Too Long During Detoning |
|
4643 |
Developer 3 (C) TC High Too Long During Detoning |
|
4644 |
Developer 4 (K) TC High Too Long During Detoning |
|
4651 |
Station 1 TC Too Low |
|
4652 |
Station 2 TC Too Low |
|
4653 |
Station 3 TC Too Low |
|
4654 |
Station 4 TC Too Low |
|
4671 |
Magenta Dry Ink Dispense Rate Too Low |
|
4672 |
Yellow Dry Ink Dispense Rate Too Low |
|
4673 |
Cyan Dry Ink Dispense Rate Too Low |
|
4674 |
Black Dry Ink Dispense Rate Too Low |
|
4722 |
ROS 2 (Y) Maximum Laser Lower Limit Exceeded |
|
4723 |
ROS 3 (C) Maximum Laser Lower Limit Exceeded |
|
4724 |
ROS 4 (K) Maximum Laser Lower Limit Exceeded |
|
4733 |
Station 3 (C) Pinscorotron Grid to PR Slope Out of Range |
|
4734 |
Station 4 (K) Pinscorotron Grid to PR Slope Out of Range |
|
4741 |
Station 1 (M) Discorotron Grid to PR Slope Out of Range |
|
4742 |
Station 2 (Y) Discorotron Grid to PR Slope Out of Range |
|
4743 |
Station 3 (C) Discorotron Grid to PR Slope Out of Range |
|
4744 |
Station 4 (K) Discorotron Grid to PR Slope Out of Bounds |
|
4753 |
Charge 3 (C) DC HVPS Fault |
|
4754 |
Charge 4 (K) DC HVPS Fault |
|
4761 |
Charge 1 (M) AC HVPS Fault |
|
4762 |
Charge 2 (Y) AC HVPS Fault |
|
4763 |
Charge 3 (C) AC HVPS Fault |
|
4764 |
Charge 4 (K) AC HVPS Fault |
|
4801 |
Developer 1 (M) and 2 (Y) Fiber Filters Inductor Missing +36VDC |
|
4803 |
Developer 3 (C) and 4 (K) Fiber Filters Inductor Missing +36VDC |
|
4811 |
Developer 1 (M) Fiber Filter Inductor Winding Fault |
|
4812 |
Developer 2 (Y) Fiber Filter Inductor Winding Fault |
|
4813 |
Developer 3 (C) Fiber Filter Inductor Winding Fault |
|
4814 |
Developer 4 (K) Fiber Filter Inductor Winding Fault |
|
4821 |
Developer 1 (M) Heater Open |
|
4822 |
Developer 2 (Y) Heater Open Circuit |
|
4823 |
Developer 3 (C) Heater Open Circuit |
|
4824 |
Developer 4 (K) Heater Open Circuit |
|
4851 |
Magenta ETAC Diffuse Reading Too Low During Calibration |
|
4852 |
Yellow ETAC Diffuse Reading Too Low During Calibration |
|
4853 |
Cyan ETAC Diffuse Reading Too Low During Calibration |
|
4881 |
Developer 1 (M) Temperature Too Low in Print |
|
4882 |
Developer 2 (Y) Temperature Too Low in Print |
|
4883 |
Developer 3 (C) Temperature Too Low in Print |
|
4884 |
Developer 4 (K) Temperature Too Low in Print |
|
4901 |
Developer 1 (M) Temperature Too High in Standby |
|
4902 |
Developer 2 (Y) Temperature Too High in Standby |
|
4903 |
Developer 3 (C) Temperature Too High in Standby |
|
4904 |
Developer 4 (K) Temperature Too High in Standby |
|
4921 |
Developer 1 (M) Temperature Too Low in Standby |
|
4922 |
Developer 2 (Y) Temperature Too Low in Standby |
|
4923 |
Developer 3 (C) Temperature Too Low in Standby |
|
4924 |
Developer 4 (K) Temperature Too Low in Standby |
|
5000 |
Developer Conditioning in Progress |
|
5101 |
Magenta Developer Near End of Life |
|
5102 |
Yellow Developer Near End of Life |
|
5103 |
Cyan Developer Near End of Life |
|
5104 |
Black Developer Near End of Life |
|
5200 |
PR Module Unlatched in Standby |
|
5201 |
PR Module Unlatched in Print |
|
5205 |
Transfer IB Cover Stock Length Mismatch |
|
5206 |
Carrier Dispense Hopper Low |
|
5207 |
Carrier Dispense Hopper Open |
|
5300 |
Run Color Maintenance Engine TRC Linearization |
|
5410 |
ILS Temperature Calibration |
|
5937 |
Dry Ink CRUM Metered / Sold Not Licensed |
|
7000 |
Pretransfer HVPS Input Voltage |
|
7001 |
Transfer/Detack HVPS Input Voltage |
|
7002 |
Preclean HVPS Input Voltage |
|
7003 |
ATA Power Supply Input Voltage |
|
7004 |
Cleaner Vacuum Checkout |
|
7005 |
AC Charge HVPS 1 Input Voltage |
|
7006 |
AC Charge HVPS 2 Input Voltage |
|
7007 |
AC Charge HVPS 3 Input Voltage |
|
7008 |
AC Charge HVPS 4 Input Voltage |
|
7011 |
DC Charge HVPS 3 Input Voltage |
|
7012 |
DC Charge HVPS 4 Input Voltage |
|
7013 |
Station 1 ESV Checkout |
|
7014 |
Station 2 ESV Checkout |
|
7015 |
Station 3 ESV Checkout |
|
7016 |
Station 4 ESV Checkout |
|
7017 |
High Developability Checkout |
|
7018 |
Low Developability Checkout |
|
7019 |
PR Belt Static Eliminator Checkout |
|
7020 |
Toner Dispenser Checkout |
|
7021 |
External Developer Drive |
|
7022 |
Patch Generator Checkout |
|
7023 |
Center ETAC Checkout |
|
7024 |
Front ETAC Checkout |
|
7025 |
Rear ETAC Checkout |
|
7026 |
PR Belt Ground Checkout |
|
7027 |
Charge Station |
|
7028 |
Developer Bias Checkout |
|
7028 |
A Developer Bias Vmag DC |
|
7028 |
B Missing Developer Bias Vdm DC |
|
7028 |
D Missing Developer Bias Vdonor AC |
|
7028 |
E Missing Developer Bias Vwd AC |
|
7028 |
F Missing HSD Enable |
|
7028 |
G Intermittent Developer Bias Checkout |
|
7029 |
dC0951 Failed To Complete |
|
7031 |
Cleaner Power Supply Input Voltage |
|
7032 |
HSD Power Supply 1 Input Voltage |
|
7033 |
HSD Power Supply 2 Input Voltage |
|
7034 |
HSD Power Supply 3 Input Voltage |
|
7035 |
HSD Power Supply 4 Input Voltage |
|
7037 |
TC Sensor Checkout |
|
7039 |
Debris/Agglomerate in Developer Material |
|
7040 |
Electrical Noise/Arcing |
|
7041 |
Xerographic NVM Checkout |
|
7042 |
Developer Subsystem Checkout - Vibration / Audible Noise |
|
7043 |
ILS Checkout Procedure |
|
7044 |
ILS Input Voltage |
|
7045 |
ILS Clamp Binding Checkout |
|
7046 |
Mag Roll Checkout |
|
7047 |
Trickle Flapper Solenoid Checkout |
|
8000 |
Maximum Limit for System Deadcycle Exceeded |
|
8002 |
Level 1 TC Recovery Run During Skipped Pitch |
|
8005 |
Purge of Aged Toner During Skipped Pitch |
|
8100 |
Consecutive Number of Skipped Pitches Exceeded One PR Belt Revolution |
|
8801 |
IOI Registration Maintenance Run During Skipped Pitch |
