XPE-08-

1203

The Lead Edge of the sheet is late to the Registration Transport Entrance Sensor (Q802A, Q802B).

1204

The Lead Edge of the sheet is late to the Registration Transport Entrance Sensor (Q802A, Q802B) from the Duplex Path.

1206

Unexpected sheet to the Registration Transport Entrance Sensor (Q802A, Q802B).

1208

The Lead Edge of the sheet is late to the Process Edge 5 Sensor (Q808) or the Trail edge of the previous sheet did not clear the sensor.

1209

The LE of the sheet is late to the Process Edge Learning Sensor (Q8015) or the TE of the previous sheet is late to the sensor.

1211

Dynamic Width check, incorrect measured process length over the Process Edge Learning Sensor (Q8015).

1229

An unexpected sheet has arrived at the PEL Sensor Q 8015.

3202

Registration Steering Controller failed self test.

3204

Registration Steering Controller Co-processor failed self test.

3205

The RSC PWB did not receive a Reg Sync signal.

3206

CCD L Sensor (Q8014) Fault.

3207

CCD 1 Sensor (Q8011) Fault.

3208

CCD 2 Sensor (Q807) Fault.

3210

RSC detected No Rephase to the Process Edge 7 Sensor (Q805) Fault.

3211

Inboard Registration Steering Motor (MOT805) not connected.

3212

Inboard Registration Steering Motor (MOT805) encoder fault.

3213

Inboard Registration Steering Motor (MOT805) encoder index fault.

3214

Inboard Registration Steering Motor (MOT805) Power Saturation Fault.

3217

RSC Inboard Registration Steering Motor (MOT805) Driver Fault.

3220

Outboard Registration Steering Motor (MOT806) not connected.

3221

Outboard Registration Steering Motor (MOT806) Encoder Fault.

3222

Outboard Registration Steering Motor (MOT806) Encoder Index Fault.

3223

Outboard Registration Steering Motor (MOT806) Power Saturation Fault.

3226

Outboard Registration Steering Motor (MOT806) Driver Fault.

3230

Sheet IDs passed between Reg applications software and RSC/PTC does not match.

3231

PTC No Registration Sync Detected

3232

PTC PLL Fault.

3233

Pretransfer Drive Motor (MOT807) not connected.

3234

Pretransfer Drive Motor (MOT807) Encoder Fault.

3236

Pretransfer Drive Motor Power Saturation RAP

3239

PTC Motor Driver Fault RAP

3245

CCD L Sensor Calibration Fault RAP

3246

CCD 1 Sensor Calibration Fault RAP

3247

CCD 2 Sensor Calibration Fault RAP

3248

CCD L Sensor LED Level Out of Range Fault RAP

3249

CCD 1 Sensor LED Level Out of Range Fault RAP

3250

CCD 2 Sensor LED Level Out of Range Fault RAP

3251

CCD L, CCD 1, or CCD 2 reads same pixel value for >=3 sheets or CCD L reads the same pixel value for >=5 sheets.

3252

CCD L, CCD 1, or CCD 2 reads maximum pixel count.

3253

Process Edge Sensors L-4 Calibration Fault RAP

3254

Process Edge Sensors 5-9 Calibration Fault RAP

3255

Process Edge Sensors L-4 LED Level Out of Range RAP

3256

Process Edge Sensors 5-9 LED Level Out of Range RAP

3257

Registration Steering Motor Rephase Minimum Time Fault RAP

3258

Registration Steering Motor Rephase to Registration Time Fault RAP

3259

Registration Steering Motor Rephase Position Fault. Lead edge of the sheet did not meet the targeted rephase position of the Registration Steering Motor.

3260

Input paper registration Process Fault. Lead edge of a sheet is outside the acceptable range for Process Registration with respect to the RegSync signal at the Process Edge 2 Sensor or CCD 1 Sensor.

3261

Input Skew Registration Fault RAP

3262

Input Lateral Registration Fault. Sheet arrived at the Process Edge 2 Sensor or CCD 1 Sensor outside the acceptable range for Lateral Position.

3263

This fault is declared when an NVM-specified consecutive number of prints MisregistrationFaultsConsecutiveNumber exceed any of the lateral thresholds at the learn sensors.

3264

This fault is declared when an NVM-specified consecutive number of prints MisregistrationFaultsConsecutiveNumber exceed any of the skew thresholds at the learn sensors.

3266

This fault is declared when an NVM-specified consecutive number of prints MisregistrationFaultsConsecutiveNumber exceed any of the process direction thresholds at the learn sensors.

3270

The Pretransfer Controller did not detect the TE of a sheet from the appropriate PE sensor during duplex registration.

3280

Preregistration Transport Motor Harness Fault RAP

3282

Preregistration Transport Motor Failed to Start RAP

3284

Preregistration Transport Motor Power Saturation RAP

3285

Registration Transport Motor Harness Fault RAP

3287

Registration Transport Motor Failed to Start RAP

3289

Registration Transport Motor Power Saturation RAP

3301

Registration Nip 1 Release Motor Missing +36VDC RAP

3302

Registration Nip 1 Release Motor Winding A Fault RAP

3303

Registration Nip 1 Release Motor Winding B Fault RAP

3305

Registration Nip 1 Release Motor Failed to Find Home RAP

3311

Registration Nip 2 Release Motor Missing +36VDC RAP

3312

Registration Nip 2 Release Motor Winding A Fault RAP

3313

Registration Nip 2 Release Motor Winding B Fault RAP

3315

Registration Nip 2 Release Motor Failed to Find Home RAP

3321

Registration Nip 3 Release Motor Missing +36VDC RAP

3322

Registration Nip 3 Release Motor Winding A Fault RAP

3323

Registration Nip 3 Release Motor Winding B Fault RAP

3325

Registration Nip 3 Release Motor Failed to Find Home RAP

3331

Registration Nip 4 Release Motor Missing +36VDC RAP

3332

Registration Nip 4 Release Motor Winding A Fault RAP

3333

Registration Nip 4 Release Motor Winding B Fault RAP

3335

Registration Nip 4 Release Motor Failed to Find Home RAP

3341

Registration Nip 5 Release Motor Missing +36VDC RAP

3342

Registration Nip 5 Release Motor Winding A Fault RAP

3343

Registration Nip 5 Release Motor Winding B Fault RAP

3345

Registration Nip 5 Release Motor Failed to Find Home RAP

5210

Sheet Before Registration Transport Entrance Sensor RAP

5220

Sheet on Registration Transport Entrance Sensor From Paper Feeder RAP

5230

Sheet between Registration Transport Entrance Sensor (Q802A, Q802B) and the Process Edge Learning Sensor (Q8015)

5240

Sheet on Process Edge L Sensor RAP

5250

Sheet between the Process Edge Learning Sensor and the Prefuser 1 Sensor.