| F1-02 | Register error on trace module. | |
| F1-03 | Unable to create one event. | |
| F1-04 | Unable to create thread. | |
| F1-05 | State object created error. | |
| F1-06 | Hundred feet object creation error. | |
| F1-07 | PRS manager creation failed. | |
| F1-08 | MOD manager creation failed. | |
| F1-09 | VWG manager creation failed. | |
| F1-0A | VIW manager creation failed. | |
| F1-0B | VDG manager creation failed. | |
| F1-0C | ENG manager creation failed. | |
| F1-0D | PPE manager creation failed. | |
| F1-0E | Calibrate creation failed. | |
| F1-0F | Reset error. | |
| F1-11 | Paper size error. | |
| F1-12 | Generated single sheet add error. | |
| F1-13 | Generated single sheet move error. | |
| F1-14 | Paper eject add error. | |
| F1-15 | Load default code page error. | |
| F1-16 | Load default character set error. | |
| F1-17 | Active default code font error. | |
| F1-18 | Memory allocation error. | |
| F1-19 | Calibrate resource creation error. | |
| F1-1A | Ejection object creation error. | |
| F1-1B | Virtual paper path sheet delete error | |
| F1-1C | Media source not found. | |
| F1-1D | Physical page characteristics object creation error. | |
| F1-1E | Generate single sheet error. | |
| F1-1F | PPE object creation error. | |
| F1-20 | Unexpected or invalid exception. | |
| F1-21 | VPL manage not ready. | |
| F1-22 | Error loading one of default fonts. | |
| F1-23 | State object setting error. | |
| F1-27 | PRT manager creation failed. | |
| F1-2B | CTG manager creation failed. | |
| F1-2D | Paper length too small for SVS calibration procedure. | |
| F1-2E | Local engine initialisation failure. | |
| F1-2F | Queued page resolution mismatch. | |
| F1-30 | INP manager creation failed | |
| F2-01 | Register error on trace module. | |
| F2-02 | Unable to create one of major events. | |
| F2-03 | Unable to create major request acknowledgement event. | |
| F2-04 | Thread pre-creation error. | |
| F2-05 | Unable to create thread. | |
| F2-06 | Thread post-creation error. | |
| F2-07 | Owner parameter creation error. | |
| F2-08 | Wait operation error. | |
| F2-09 | Acknowledgement message out of context. | |
| F2-0A | Message queue error. | |
| F2-0B | Invalid parameter. | |
| F2-0C | Out of memory. | |
| F2-0D | Unexpected/invalid exception. | |
| F2-0E | Manage not ready. | |
| F4-01 | Unable to create one event. | |
| F4-02 | Invalid device state error. | |
| F4-03 | Parsing error. | |
| F4-03 | Insufficient memory to run job. | |
| F4-04 | Invalid control unit state/event. | |
| F4-05 | Control unit read error on input file. | |
| F4-06 | Control unit in premature end of file. | |
| F4-07 | Parity error too frequent. | |
| F4-08 | Overrun error too frequent. | |
| F4-09 | Data transfer time-out. | |
| F4-0A | Cannot enable. | |
| F4-0B | ISS during an invalid CU state. | |
| F4-0C | Hardware disable switch activated. | |
| F4-0D | Input attachment error. | |
| F4-0E | Unknown attachment type. | |
| F4-0F | Invalid emulation. | |
| F4-10 | File not found or access denied. | |
| F4-11 | Invalid two channel switch. | |
| F4-12 | Invalid channel transfer mode. | |
| F4-13 | Invalid TCP/IP link. | |
| F4-14 | Invalid TCP/IP port. | |
| F4-15 | Invalid IP address. | |
| F4-16 | Invalid subnet mask. | |
| F4-17 | Invalid gateway. | |
| F4-18 | IP address conflict. | |
| F4-19 | Link out of range. | |
| F4-1A | Link not available | |
| F4-1B | Media not supported. | |
| F4-1C | Invalid printing page count. | |
| F4-1D | Invalid page buffer depth. | |
| F4-1E | Invalid sense pipe name. | |
| F4-20 | Error loading one of default fonts. | |
| F4-21 | Paper length change not allowed. | |
| F4-23 | Software 2-up not allowed. Software 2-up not supported in line mode and attachment because hardware 2-up is enabled. | |
| F4-24 | Software 2-up requested page does not fit. Invalid software 2-up parameter in line mode. | |
| F4-25 | Unsupported software force n-up for attachment. Software 2-up not supported in test attachment. | |
| F4-26 | Unsupported duplex in line mode emulation. | |
| F4-27 | This fault can only occur when in support mode. It occurs when the user attempts to read (View) the InputTrace.dta file, at the same time as the data trace is enabled for write (A conflict of reading and writing to the same file). | |
| F4-28 | Front end host PPR/PPD protocol error. | |
| F4-29 | Front end host PPR/PPD buffer overflow. | |
| F4-2A | Front end host PPR/PPD header transfer time-out. | |
| F4-2B | Front end host PPR/PPD data transfer time-out. |
