...to avoid scrolling this long list, press the 'blackberry' button, select 'Find', input the last 3 digits...
|
010-311 |
Fuser Heat Roll STS-1 Disconnection Fail |
Fuser Heat Roll STS-1 Open Wire is detected. |
|
010-312 |
Fuser Heat Roll STS-2 Disconnection Fail |
Fuser Heat Roll STS-2 Open Wire is detected. |
|
010-313 |
Fuser Heat Roll STS-3 Disconnection Fail |
Fuser Heat Roll STS-3 Open Wire is detected. |
|
010-315 |
Fuser Latch Contact Fail |
Nip Sensor does not turn ON a spec time after the Latch On signal is sent. |
|
010-316 |
Fuser Latch Retract Fail |
Nip Sensor does not turn OFF a spec time after the Latch Off signal is sent. |
|
010-317 |
Not Ready Heat RollFuser On Time Fail |
Heat Roll does not reach print-ready temp a spec time after printing stops due to Low Temp Not Ready or High Temp Not Ready. |
|
010-320 |
Heat Roll Over Heat Fail |
It is detected that one of Fuser Heat Roll STS-1, Fuser Heat Roll STS-2 and Fuser Heat Roll STS-3 is at high temperature. |
|
010-320 |
Heat Roll Over Heat Fail |
It is detected that one of Fuser Heat Roll STS-1, Fuser Heat Roll STS-2 and Fuser Heat Roll STS-3 is at high temperature. |
|
010-327 |
Standby Heat Roll Fuser On Time Fail |
In Wait Mode, one of Main Lamp 1, Main Lamp 2 and Sub Lamp abnormally stays ON. |
|
010-330 |
Fuser Motor Fail |
A detection of Fuser Motor rotation failure. |
|
010-400 |
Fuser Web Near End |
Fuser Web replacement time is near. |
|
010-910 |
Fuser Web End |
Fuser Web needs replacing. |
|
012-100 |
Decurler In Sensor ON Jam |
Decurler In Sensor does not turn ON a spec time after IOT Exit Sensor ON. |
|
012-101 |
Decurler Out Sensor ON Jam |
Decurler Out Sensor does no turn ON a spec time after Decurler In Sensor ON. |
|
012-102 |
Punch Out |
Punch Out Sensor does not turn ON a spec time after Decurler Out Sensor ON or Folder Exit Sensor ON. |
|
012-103 |
Punch Out Sensor OFF Jam |
• Punch Out Sensor does not turn OFF a spec time after Punch Out Sensor ON. |
|
012-104 |
Interposer Feed Out Sensor ON Jam |
Feed Out Sensor does not turn ON a spec time after Interposer Nudger Solenoid ON. |
|
012-108 |
Folder Path Sensor-3 OFF Jam |
Folder Path Sensor-3 does not turn OFF a spec time after Folder Path Sensor-3 ON |
|
012-109 |
Interposer Feed Out Sensor OFF Jam |
Feed Out Sensor does not turn OFF a spec time after Feed Out Sensor ON. |
|
012-113 |
Booklet In Sensor ON Jam |
Booklet In Sensor does not turn ON a spec time after Punch Out Sensor ON. |
|
012-114 |
Booklet In Sensor OFF Jam 1 |
• Booklet In Sensor does not turn OFF within a spec time. |
|
012-115 |
Booklet Folder Roll Exit |
Booklet Folder Roll Exit Sensor does not turn OFF a spec time after Booklet Folder Roll Exit Sensor ON. |
|
012-117 |
Folder Exit Sensor ON Jam |
Fold: Folder Exit Sensor does not turn ON a spec time after Folder Entrance Sensor ON. |
|
012-118 |
Folder Path Sensor 2 ON Jam |
Folder Path Sensor-2 does not turn ON a spec time after Folder Entrance Sensor ON. |
|
012-119 |
Folder Path Sensor 3 ON Jam |
Folder Path Sensor-3 does not turn ON a spec time after Folder Path Sensor-2 ON. |
|
012-120 |
Folder Path Sensor 4 ON Jam |
Folder Path Sensor-4 does not turn ON a spec time after Folder Path Sensor-3 ON. |
|
012-141 |
Buffer Path Sensor OFF Jam |
1. The TE of the 2nd paper for buffer does not turn OFF Buffer Path Sensor a spec time after the LE of the 2nd buffer paper turns ON Punch Out Sensor. |
|
012-142 |
Buffer Path Sensor ON Jam |
When Buffer Paper in use: |
|
012-151 |
Compile Exit Sensor OFF Jam |
Compile Exit Sensor does not turn OFF a spec time after Compile Exit Sensor ON. |
|
012-152 |
Compile Exit |
Punch Mode OFF: Compile Exit Sensor does not turn ON a spec time after Punch Out Sensor ON. |
|
012-159 |
Eject |
Punch Mode OFF: Eject Sensor does not turn ON a spec time after Compile Exit Sensor ON. |
|
012-160 |
Eject Sensor OFF Jam |
Eject Sensor does not turn OFF a spec time after Eject Sensor ON. |
|
012-161 |
Set Eject Jam |
Compile Exit Sensor does not turn OFF a spec time after the start of eject. |
|
012-171 |
Top Tray Exit Sensor ON Jam |
Punch Mode OFF: Top Tray Exit Sensor does not turn ON a spec time after Punch Out Sensor ON. |
|
012-172 |
Top Tray Exit Sensor OFF Jam |
• The TE of paper does not turn OFF Top Tray Exit Sensor a spec time after the LE of it turns ON Punch Out Sensor. |
|
012-180 |
Booklet Folder Roll Exit Sensor OFF Jam |
Booklet Folder Roll Exit Sensor does not turn OFF a spec time after Booklet Folder Roll Exit Sensor ON. |
|
012-211 |
Stacker Tray Fail |
1. Stack Height Sensor does not turn OFF 500msec after Stack Tray starts lowering. |
|
012-212 |
Stacker Tray Upper Limit Fail |
Stack Height Sensor 2 turned ON after Stacker Tray started lifting up. |
|
012-213 |
Stacker Tray Lower Limit Fail |
Lower Limit Sensor turned ON after Stacker Tray started lowering. |
|
012-214 |
End Wall Home Sensor OFF Fail |
End Wall Home Sensor does not turn OFF a spec time after End wall Motor ON |
|
012-215 |
End Wall Open Sensor ON Fail |
End Wall Open Sensor does not turn ON a spec time after End wall Motor ON |
|
012-216 |
End Wall Home Sensor ON Fail |
End Wall Home Sensor does not turn ON a spec time after End Wall Motor ON. |
|
012-217 |
End Wall Open Sensor OFF Fail |
End Wall Open Sensor does not turn OFF a spec time after End wall Motor ON. |
|
012-218 |
Shelf Home Sensor ON Fail |
1. Shelf Home Sensor does not turn ON a spec time Shelf Motor ON. |
|
012-219 |
Shelf Home Sensor OFF Fail |
1. Shelf Home Sensor does not turn OFF a spec time after Shelf Motor ON. |
|
012-221 |
Tamper Home Sensor ON Fail |
Tamper Home Sensor does not turn ON a spec time after Tamper Motor ON. |
|
012-223 |
Tamper Home Sensor OFF Fail |
Tamper Home Sensor does not turn OFF after Tamper Motor stops after Tamper Home Sensor OFF. |
|
012-225 |
Booklet Tamper F Home Sensor ON Fail |
In returning Booklet Tamper F home, Booklet Tamper Home Sensor (F) does not turn ON a spec time after Booklet Tamper Motor (F) ON. |
|
012-226 |
Booklet Tamper F Home Sensor OFF Fail |
Booklet Tamper Home Sensor (F) does not turn OFF a spec time after Booklet Tamper Motor (F) ON. |
|
012-227 |
Booklet End Guide Home Sensor OFF Fail |
Booklet End Guide Home Sensor does not turn OFF a spec time after Booklet End Guide Motor ON. |
|
012-228 |
Booklet End Guide Home Sensor ON Fail |
In returning Booklet End Guide home, Booklet End Guide Home Sensor does not turn ON a spec time after Booklet End Guide Motor ON. |
|
012-229 |
Booklet Tamper R Home Sensor ON Fail |
In returning Booklet Tamper R home, Booklet Tamper Home Sensor (R) does not turn ON a spec time after Booklet Tamper Motor (R) ON |
|
012-230 |
Booklet Tamper R Home Sensor OFF Fail |
Booklet Tamper Home Sensor (R) does not turn OFF a spec time after Booklet Tamper Motor (R) ON |
|
012-235 |
Staple Move Home Sensor ON Fail |
1. Staple Move Home Sensor does not turn ON a spec time after Staple Move Motor ON. |
|
012-235 |
Staple Move Home Sensor ON Fail |
1. Staple Move Home Sensor does not turn ON a spec time after Staple Move Motor ON. |
|
012-237 |
|
1. |
|
012-238 |
|
1. |
|
012-239 |
Sub Paddle Home Sensor ON Fail |
Sub Paddle Home Sensor does not turn ON a spec time after Sub Paddle Home Sensor OFF. |
|
012-240 |
Sub Paddle Home Sensor OFF Fail |
Sub Paddle Home Sensor does not turn OFF a spec time after Sub Paddle Up/Down Solenoid ON. |
|
012-241 |
Booklet Knife Folding Sensor Fail |
In the folding operation by the Booklet Knife, Knife Folding Sensor does not turn ON a spec time after Knife Clutch ON. |
|
012-243 |
Booklet Knife Home Sensor ON Fail |
• In returning Booklet Knife home, Knife Home Sensor does not turn ON a spec time after Knife Clutch ON. |
|
012-246 |
Booklet Stapler Fail |
1. Stapler Ready Signal does not become Ready (does not staple) a spec time after Booklet Stapler Start Signal ON. |
|
012-247 |
Side Regi Sensor OFF Fail |
1. Side Regi Sensor does not turn OFF a spec time after Puncher Move Motor ON. |
|
012-248 |
Compile Stacker Tray Offset Fail |
Stacker Front Position Sensor does not turn ON a spec time after Stacker Offset Motor ON. |
|
012-250 |
End Guide Motor 1 Start Fail |
When End Guide 1 starts moving from Home, End Guide Home Sensor 1 does not turn OFF a spec time after End Guide Motor 1 ON. |
|
012-251 |
End Guide Motor 2 Start Fail |
When End Guide 2 starts moving from Home, End Guide Home Sensor 2 does not turn OFF a spec time after End Guide Motor 2 ON. |
|
012-252 |
End Guide Motor 1 Home Fail |
When End Guide 1 starts moving home, End Guide Home Sensor 1 does not turn ON a spec time after End Guide Motor1 ON |
|
012-253 |
End Guide Motor 2 Home Fail |
When End Guide 1 starts moving home, End Guide Home Sensor 2 does not turn ON a spec time after End Guide Motor 2 ON. |
|
012-254 |
Envelope Folder Tray Broken |
Folder Envelope Tray Switch does not turn OFF a spec time after Envelope Tray Lock Solenoid ON.ÅA |
|
012-255 |
Interposer Tray Up Fail |
Level Up Sensor does not turn OFF a spec time after Interposer Tray Up/Down Motor starts the up operation. |
|
012-260 |
Eject Clamp Up |
1. Eject Up Sensor does not turn ON a spec time after Eject Clamp Motor ON. |
|
012-264 |
Booklet Drawer Broken Fail |
When Finisher Front Door Interlock was closed, Booklet Drawer Set Sensor sensed it was open. |
|
012-265 |
Booklet Knife Home Sensor OFF Fail |
When Booklet Knife leaves Home, Knife Home Sensor does not turn OFF a spec time after Knife Clutch ON. |
|
012-282 |
Eject Clamp Up Sensor OFF Fail |
1. Eject Up Sensor does not turn OFF a spec time after Eject Clamp Motor ON. |
|
012-291 |
Stapler Fail |
• The state of Staple Home Sensor did not change from OFF to ON a spec time after Staple |
|
012-302 |
Finisher Front Door Interlock Open |
Finisher Front Door is open. |
|
012-304 |
I/F Module Front Door Interlock Open |
I/F Module Front Door is open. |
|
012-306 |
Interporser Top Cover Open |
Interposer Top Cover is open. |
|
012-307 |
Booklet Drawer Set Fail |
Booklet Drawer is not installed. |
|
012-320 |
Punch Home Sensor ON Fail |
Punch Home Sensor did not turn ON a spec time after Puncher Motor ON. |
|
012-321 |
Punch Home Sensor OFF Fail |
Punch Home Sensor does not turn OFF a spec time after Puncher Motor ON. |
|
012-322 |
Puncher Move Home Sensor OFF Fail |
1. Punch Move Home Sensor does not turn OFF a spec time after Puncher Move Motor ON. |
|
012-323 |
Puncher Move Home Sensor ON Fail |
1. Punch Move Home Sensor did not turn ON a spec time after Puncher Move Motor ON. |
|
012-324 |
Side Regi Home Sensor OFF Fail |
1. Side Regi Home Sensor does not turn OFF a spec time after Puncher Move Motor ON. |
|
012-325 |
Side Regi Home Sensor ON Fail |
1. Side Regi Home Sensor does not turn ON a spec time after Puncher Move Motor ON. |
|
012-330 |
Decurler Cam Home Sensor OFF Fail |
Decurler Cam Home Sensor does not turn OFF a spec time after Decurler Cam Clutch On. |
|
012-332 |
Decurler Cam Home Sensor ON Fail |
1. Decurler Cam Home Sensor does not turn ON a spec time after Decurler Cam Home Sensor OFF. |
|
012-334 |
Download Mode Fail |
Download aborted, causing the MC to start only in Download Mode at |
|
012-900 |
Buffer Path Sensor Static Jam |
At Power ON, or with all Interlocks closed, or in Initialize operation, Buffer Path Sensor detected paper. |
|
012-903 |
Compile Exit Sensor Static Jam |
At Power ON, or with all Interlocks closed, or in Initialize operation, Compile Exit Sensor detected paper. |
|
012-905 |
Compile Tray No Paper Sensor Static Jam |
At |
|
012-907 |
Top Tray Exit Sensor Static Jam |
At Power ON, or with all Interlocks closed, or in Initialize operation, Top Tray Exit Sensor detected paper. |
|
012-908 |
Eject Sensor Static Jam |
At Power ON, or with all Interlocks closed, or in Initialize operation, Eject Sensor detected paper. |
|
012-909 |
Punch Out Sensor Static Jam |
At Power ON, or with all Interlocks closed, or in Initialize operation, Punch Out Sensor detected paper. |
|
012-938 |
Decurler In Sensor Static Jam |
At Power ON, or with all Interlocks closed, or in Initialize operation, Decurler In Sensor detected paper. |
|
012-939 |
Decurler Out Sensor Static Jam |
At Power ON, or with all Interlocks closed, or in Initialize operation, Decurler Out Sensor detected paper. |
|
012-949 |
Punch Box Set Fail |
Punch Box Set Sensor detected OFF (no Punch Box). |
