005-

005-121

DADF Feed Sensor ON Jam

1. Feed Sensor does not turn ON a spec time after the start of Pre-Feed.

005-122

DADF Simplex/Side 1 Pre Regi Sensor ON Jam

1. Pre-Regi Sensor does not turn ON for the 1st doc a spec time after Feed Sensor ON.

005-123

DADF Simplex/Side 1 Regi Sensor ON Jam

Regi Sensor does not turn ON a spec time after Pre-Regi Sensor ON.

005-124

DADF Lead Regi Sensor ON Jam

Lead Regi Sensor does not turn ON a spec time after the start of scan (Regi Motor ON).

005-125

DADF Regi Sensor OFF Jam

Regi Sensor does not turn OFF a spec time after the start of scan (Regi Motor ON).

005-126

DADF Out Sensor ON Jam

Out Sensor does not turn ON a spec time after the start of scan (Regi Motor ON).

005-127

DADF Out Sensor OFF Jam

Out Sensor does not turn OFF a spec time after Regi Sensor OFF.

005-128

DADF Exit Sensor 1 ON Jam (Simplex Mode)

In Simplex Mode, Exit Sensor 1 does not turn ON a spec time after Out Sensor ON.

005-129

DADF Exit Sensor 1 OFF Jam (Simplex Mode)

In Simplex Mode, Exit Sensor 1 does not turn OFF a spec time after Out Sensor OFF.

005-130

DADF Invert Sensor ON Jam (Duplex Mode)

In Duplex Mode, Invert Sensor does not turn ON a spec time after Out Sensor ON.

005-133

DADF Invert Sensor OFF Jam

In Duplex Mode, Invert Sensor does not turn OFF a spec time after Out Sensor OFF.

005-135

DADF Pre Regi Sensor ON Jam (during Invert operation)

During the Invert operation, Pre-

005-136

DADF Regi Sensor ON Jam (during Invert operation)

During the Invert operation, Regi. Sensor does not turn ON a spec time after Pre-Regi Sensor ON.

005-137

DADF Exit Sensor 2 ON Jam

In the inverting output operation, Exit Sensor 2 does not turn ON a spec time after Feed Motor starts rotating backward.

005-138

DADF Exit Sensor 1 ON Jam

In the inverting output operation, Exit Sensor 1 does not turn ON a spec time after Exit Sensor 2 ON.

005-141

DADF Feed Sensor OFF Jam

Pre-Regi Sensor turned OFF before Feed Sensor turned OFF. (multifeed/stream feed)

005-142

DADF Exit Sensor 1 OFF Jam(Duplex Mode)

In the inverting output operation, Exit Sensor 1 does not turn OFF a spec time after Exit Sensor 2 OFF.

005-143

DADF Exit Sensor 2 OFF Jam

Exit Sensor 2 does not turn OFF a spec time after Exit Sensor 2 ON.

005-144

DADF Too First Pre Regi Sensor ON Jam

Pre Regi Sensor turned ON earlier than a spec timing due to doc skew.

005-150

DADF Feed Sensor OFF Jam (Punched Doc Mode)

In Punched Doc Mode, Feed Sensor does not turn OFF a spec time after Feed Sensor ON.

005-151

DADF Pre Regi Sensor OFF Jam (Punched Doc Mode)

In Punched Doc Mode, Pre Regi Sensor does not turn OFF a spec time after Pre Regi Sensor ON.

005-152

DADF Regi Sensor OFF Jam (Punched Doc Mode)

In Punched Doc Mode, Regi Sensor does not turn OFF a spec time after Regi Sensor ON.

005-153

DADF Regi Sensor OFF Jam (Punched Doc Mode)

In Punched Doc Mode, Lead Regi Sensor does not turn OFF a spec time after Lead Regi Sensor ON.

005-154

DADF Out Sensor OFF Jam (Punched Doc Mode)

In Punched Doc Mode, Out Sensor does not turn OFF a spec time after Out Sensor ON.

005-155

DADF Exit Sensor 1 OFF Jam (Punched Doc Mode) (Simplex)

In Punched Doc Mode, Exit Sensor 1 does not turn OFF a spec time after Exit Sensor 1 ON. (Simplex)

005-156

DADF Exit Sensor 1 OFF Jam (Punched Doc Mode (Duplex)

In Punched Doc Mode, Exit Sensor 1 does not turn OFF a spec time after Exit Sensor 1 ON.

005-157

DADF Invert Sensor OFF Jam (Punched Doc Mode)

In Punched Doc Mode, Invert Sensor does not turn OFF a spec time after Invert Sensor ON.

005-158

DADF Exit Sensor 2 OFF Jam (Punched Doc Mode)

In Punched Doc Mode, Exit Sensor 2 does not turn OFF a spec time after Exit Sensor 2 ON.

005-160

DADF Tray Lift Up Fail (Document Set) (during Job)

It is detected that with paper loaded, a spec time after Tray starts lifting up, Level Sensor does not turn ON or that Bottom Sensor does not turn OFF. (Applicable to the case where this is detected with MC running/not in operation/purging)

005-190

Feed Motor Logic Jam

The Invert operation could not start 160ms after the doc trail edge turned OFF the Invert Sensor.

005-194

Size Mismatch Jam on Slow Scan Mix Size

It is detected that with "Slow Scan MIX" selected, size in fast scan is different from doc guide width.

005-196

Size Mismatch Jam on No Mix Size

It is detected that the 2nd doc and subsequent ones include doc(s) different in size from the 1st one.

005-197

Prohibit Combine Size Jam

A prohibited combination of sizes is detected.

005-198

Too Short Size Jam

A doc is too short in fast scan to be transported. (The TE of the doc passes on Feed Sensor before the LE reaches Pre Regi Sensor.)

005-199

Too Long Size Jam

It is detected that a doc is too long in slow scan for DADF to transport.

005-275

DADF RAM Fail

Defective DADF PWB RAM was detected.(A check is made at Power ON.)

005-280

DADF EEPROM Fail

An error in writing into or communicating with DADF EEPROM was detected.

005-281

DADF Tray Lift Down Fail

Bottom Sensor does not turn ON a spec time after DADF Tray starts lowering.

005-282

DADF Tray Lift Up Fail (No Document)

In the initialize operation with no doc loaded, Bottom Sensor does not turn off a spec time after Tray starts lifting up.

005-283

DADF Level Sensor Logic Fail

Level Sensor Fail or Nudger Solenoid Fail was logically detected in relation to DOC Sensor output.

005-284

DADF APS Sensor Logic Fail

An illogical combination of APS Sensors 1~3 outputs

005-285

DADF Nudger Lift Up Fail

It is detected that Nudger Position SNR does not turn ON 350msec after Nudger Lift Motor starts rotating backward, or that Nudger Position SNR does not turn OFF 250msec after NudgeÇí Lift Motor starts rotating forward.

005-286

DADF Feed Out Sensor Fail

During doc feed, Pre Regi Sensor turned OFF before Feed Sensor turned OFF

005-302

DADF Feeder Cover Interlock Open

The DADF Feeder Cover Interlock is open.

005-303

DADF Tray Interlock Open

DADF Tray Interlock is open.

005-304

Platen Interlock Open

While the DADF was in operation, the Platen Interlock became open.

005-305

DADF Feeder Cover Interlock Open (Running)

While the DADF was in operation, the Feeder Cover Interlock became open.

005-306

DADF Tray Interlock Open (Running)

While the DADF was in operation, the Tray Interlock became open.

005-308

DADF L/H Cover Interlock Open

The DADF L/H Cover Interlock is open.

005-309

DADF L/H Cover Interlock Open (Running)

While the DADF was in operation, the L/H Interlock became open.

005-906

DADF Feed Sensor Static Jam

Feed Sensor turns ON at the following timings:

005-907

DADF Pre Regi Sensor Static Jam

Pre-Regi Sensor turns ON at the following timings:

005-908

DADF Regi Sensor Static Jam

Regi Sensor turns ON at the following timings:

005-909

DADF Lead Regi Sensor Static Jam

Lead Regi Sensor turns ON at the following timings:

005-910

DADF Out Sensor Static Jam

Out Sensor turns ON at the following timings:

005-911

DADF Exit Sensor 1 Static Jam

Exit Sensor 1 turns ON at the following timings:

005-912

DADF Exit Sensor 2 Static Jam

Exit Sensor 2 turns ON at the following timings:

005-913

DADF Invert Sensor Static Jam

Invert Sensor 1 turns ON at the following timings:

005-914

DADF No. 1/2/3 APS Sensor Static Jam

No. 1/2/3 APS Sensor turns ON at the following timings:

005-918

DADF Invert Sensor 2 Static Jam

Invert Sensor 2 turns ON at the following timings:

005-919

DADF Tray Lift Up Fail (Document Set)

It is detected that with docs loaded, a spec time after Tray starts lifting up Level Sensor does

005-940

DADF No Original Fail

It is detected that a doc is pulled out.

005-941

DADF Not Enough Document

It is detected that the qty of docs is short of the full qty after the reloading of all.

005-942

DADF Tray Stack Over Fail

It was detected that when Nudger Solenoid was pulled in at the start of a job Level Sensor did not turn OFF.